11 Feb 2011 Ted arrived to find a porch with rotten tongue-and-groove decking, disintegrating steps, falling-off balusters, After gluing the first three boards together, Ted and Mike blind-nail the rest of the decking boards into place.
14 Dec 2017 Add character and pizazz to your porch with a V-groove pine ceiling. Follow these steps and increase to prevent splitting the wood. On the tongue side, nail it through the tongue at an angle so the next row covers the nail.
AsktheBuilder: porch decking needs to be prepared and installed properly to get a lasting porch. Composite porch porch Decking. This is real Douglas Fir porch decking. It's tongue and groove allowing the nails to be hidden. Copyright
Predrill all screw and nail holes due to the hardness of the wood. Use stainless steel screws or nails for installation. Slope the flooring slightly, so rainwater will run off of it. When using tongue and groove lumber, leave a small gap every few
5 Apr 2001 Article about installing tongue-and-groove flooring on a porch. I took a risk with this tool, as 2 inch finish nails do not have as much holding power as other flooring fasteners. But after 18 months in use, none of the planks
One thing you'll really want to consider is renting a couple of nail guns and a compressor, if you don't already have them. Sure, you can .. for a plainer profile, install tongue-and-groove flooring on your porch ceiling, then paint or stain it.
Q: I need to replace some rotten tongue and groove porch floorboards that were installed only a few years ago. I blind-nail the floor boards into the joists by driving 8d galvanized finish nails at a 45 degree angle starting at the back of the
5/4 x 4 x 10 tongue and groove Deck Board - Use to add country charm to your home decor. to blind nail or use mastic so that unsightly nails do not show in your final project; This is a tongue and groove item; Kiln dried; 5/4 in. x 4 in. x 10 ft.
Make the cut in a damaged board that's next to a good one and whose groove faces the other boards that will be Toenail (pound at an angle) a stainless-steel ring-shark siding nail through the tongue of the new board and into each joist.
To fill the gap between the last board and the wall, take a series of measurements along the gap. Use the narrowest of the measurements to rip the last board. Use a flatbar to get the tongue and groove joints to fit tightly. Face-nail last strip into
20 Jun 2008 Between drifting snow and big storms that hit the house sideways, even covered porches take a beating. The hardest hit The hardest hit are traditional, solid surface, tongue-and-groove floors without gaps for drainage like a deck. But there But if you're springing for cedar, redwood or some other great-looking lumber, no nails is a finishing touch that really showcases the investment.
Watch this video to find out how to remove a rotten wood porch floor, and replace it with pressure treated pine floor joists and tongue and groove flooring. Blind-nail the flooring in the tongue using galvanized or stainless steel finishing nails.
Properly installed porch flooring makes a great first impression. Installing tongue and groove flooring, specifically, AZEK porch decking, is not difficult. . Nail a piece of wood (plywood) to the top of the 2x4s to protect the beam's surface.
of Perennial Wood porch flooring This detailed guide provides you with step-by-step installation instructions This path of a screw, nail, or possibly a larger drill bit. Shims — Thin stability, tongue-and-groove porch flooring should always.
20 Jul 2017 I have built a covered porch off the back of our house, about 15' to the deck off of the ground, which will ultimately be I will install PT, tongue & groove, KDAT, flooring on a 2 x 12, 12" (on center). steel finishing nails, or 2" cut galvanized or stainless steel nails, and possibly pre-drilling each tongue of the
20 Aug 2014 tongue and groove porch Floor Installation Installing a tongue and groove porch floor is completely doable! Circular Saw; Tape Measure; Nail Gun; nails; Rubber Mallet; Felt Paper; tongue and groove porch Decking
DEAR ROBERT: tongue and groove wood porch flooring is a classic look. step is to remove the slivers of the tongue that are pinned in place by the nails used to fasten the original tongue and groove strip of lumber to the porch floor joists.
A carpenter replaced all the old deck boards on our front porch with 1x4 tongue-and-groove fir graded "D & BTR Mix-grain. What puzzles me most about your photos is that I don't see any nails where the flooring has buckled. If there aren't